Can I Install a Bath Tub Myself? Factors to Consider And Actions
Can I Install a Bath Tub Myself? Factors to Consider And Actions
Blog Article
This post down below pertaining to How to Install a Bathtub is particularly remarkable. Give it a try and make your own ideas.
Setting up a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a new one is likewise a moderately hard job. If the old bathtub is easily obtainable, the job can relocate immediately; if you have to open up a wall to get rid of the old tub and also position the new tub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will need an assistant to move out the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the task and fit attempting it. Instead of hiring a service provider to take over a halfway-completed job, it is far better to think about utilizing one before you start. Chances are you may require an expert plumber to make tube links.
This short article will certainly help you set up a new tub in your washroom if you have already acquired a new bathtub and don't require to change the plan of your previous water pipes.
Your tools and also product checklist must comprise the following:
Preparing for the Setup
To start with, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to prevent pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its last setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wooden boards under its feet, position the bathtub in the required placement. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub till the level checks out degree.
To set up faucets, fit all-time low of the outermost versatile tap adapter to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
Activate the water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as additionally examine the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait till the bathtub has actually been utilized at least when as this will resolve it right into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washing machines are in place between the tap and also the sink. Safeguard the tap in place with the maker provided backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall in between the bathroom and also the tiling, leading to problems with moisture and also feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and also can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can split relatively early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our piece on How to Install a Bathtub Yourself. Thanks a ton for taking the time to browse our content. Loved our write up? Please share it. Let others find it. Thank-you for taking the time to read it.
Book Today!
Report this page